(0 item) - $0.00

You have no items in your shopping cart.

section

JTC Valve Sales

  • Fusible Plugs - An Essential Safety Valve & Pressure Relief Device

    Fusible plugs are used to keep the temperature of the fusible metal below its melting point. The fuse plugs operate as a safety valve when abnormal or dangerous temperatures build up in a closed vessel. They have low melting points, making them useful to be used in mechanisms that require high-temperature settings. Due to this characteristic, they are used on some boilers to provide added protection against low water level.

    Fuse Plugs Fuse Plugs

    This fluid coupling overheating protection device is a needed component in your industrial set up. Constructed of bronze or brass, the pipe plug has a tapered hole, which is drilled through the length of the valve. It has an even tapered from end to end that is filled with a low melting alloy – mostly consisting of tin. Fusible plugs are of two types:

    • FIRE-ACTUATED: The boiler plug is an alloy of tin, copper & lead and has a melting point of 6° to 7°. One end of the plug is attached to the tire/hot gases while the other is in contact with water. In case the water level drops below the plug, tin melts and blows out. It will produce a whistling noise to warn the operator that it’s time to replace the plug.
    •  STEAM-ACTUATED: The plug is installed on the end of the pipe outside the drum. The other end of the plug is kept at the lowest permissible water level in the steam drum. The metal in the plug melts at a temperature below that of the steam in the boiler. The water around the plug is at a cooler temperature than that in the boiler as long as the pipe end is below water level. When the water level drops below the open end of the pipe, steam heats the fuse plug, which melts down the tin letting out a warning to the operator.

    It is important to maintain the fusible plugs and replace them every year. Do not try to refill the old casings with new tin alloy as this would only harm the material and lead to a dangerous effect. It is advised to always use a new plug.

    You have arrived at the right place to search for a new fusible plug. At JTC Valve Sales,  https://www.jtcvalvesales.com/blog we stock only high-quality valves and their accessories to maintain the specific standards demanded by the industries. You can get in touch with us at 440-346-1259 to discuss the specifications before you purchase.

  • 7 Steps about How to Inflate a Helium Balloon Using Latex Inflators

    Helium balloons exist almost everywhere there is a celebration. And it’s simple too!

    Here are 7 easy and quick steps that will help you to inflate helium balloons on your own.

    1. Get a helium tank: Helium is required to fill in the balloons. You can either rent a tank or buy one. Renting is a good option if you rarely party. But if you party hard often, it is better to buy one and use all the helium in the cylinder till it lasts.
    2. Buy the balloons: Whoa! There is a huge variety out there. But don’t buy the normal rubber birthday balloons as they won’t stay afloat for long. Instead, the shiny mylar balloons of those made of latex would make a better choice.
    3. Place the valve over the nozzle of helium tank: Ensure that the valve end fits well into the open end of the balloon so that there is no leakage. Also, check the balloon for any holes.
    4. Switch on the balloon inflator to let the gas out: Now, you can allow the latex/mylar balloon filler to escape the gas at required pressure.
    5. Observe the inflation & stop when the balloon is full: Keep an eye on the balloon & check how much blown up you want it to be. Most of the mylar balloon inflators automatically shut off when the balloon is stretched to its maximum.
    6. Remove the balloon systematically: This would require a bit of diligence. You need to pinch the end of the balloon and stretch it to take it off the valve.
    7. Tie the string: There are balloon inflators that tie the balloons for you. However, you can also tie it on your own. Preferably, tie some sort of weight to the balloon so that it doesn’t fly off.

    It is really simple, isn’t it? Now, if you are looking out for ordering a balloon inflator that perfectly fits into your helium cylinder, contact 440-346-1259 to speak to the professionals of JTC Valve Sales, leading providers of industrial valves & regulators. Visit https://www.jtcvalvesales.com/blog/Latex-and-Mylar-Balloon-Fillers/ to browse through our list of offerings.

  • How Do You Prevent Overfilling of Helium Balloons?

    Filling or overfilling of balloons is a machine’s work now. It is no longer a cumbersome human task. Various varieties of balloon fillers have been introduced till date and every model possesses certain specifications. While these fillers are at work, you might be worried about any unexpected mishaps that could cause life-threatening damages. One of such dangers is helium leakage or bursting of the balloons on overfilling.

    The balloon inflators with push down valves are designed to fill both latex and/or mylar balloons with one unit. For your convenience, most of the mylar balloon inflators shut off automatically when the balloon is full. So, you do not have to monitor constantly. The mylar fillers are available with or without hand-tight connection and may or may not have cylinder contents gauge. The hand-tight cylinder connection doesn’t require a wrench for installation and the rubber tilt valve easily controls the gas and allows it to be replaced.

    Latex Push Down Inflators Latex Push Down Inflators

    The latex and mylar balloon fillers possess mechanisms that can offer desired shapes and sizes to your balloons. They also help in avoiding gas leakages and overfilling of gases. So, these are essential items in your industrial utility kit. Whenever you think of having a small get together or plan a grand celebration, just pull out the balloon inflator and start shaping helium into colors and shapes. It’s real fun at any age!

    Now, if you are looking out for a trusted source for purchasing quality balloon fillers for both mylar and latex balloons, JTC Valve Sales is the right place. We are industry players since years and have a range of unchallenged quality industrial products. You can browse through our online store and place an order when you find the product you are looking out for. Visit https://www.jtcvalvesales.com/blog/balloon-inflators/ for more information.

  • How Dust Caps Prevent Connectors from Wearing Out

    Looking for the smallest details in the industrial equipment is really crucial. are tiny instruments that are used to protect the pins of connectors when there are no cables attached to the loose end. Made of plastic or metal, these connector caps also shield against electromagnetic interference EMI issues. Many of the metal valve caps  covercome with an attached chain to secure the chassis. The metal chain ensures that the cap is not misplaced when it is disconnected for cable attachment.

    DUST CAP AND CHAIN DUST CAP AND CHAIN

    Here are some important points to be considered while using dust covers:

     Check whether the dust cap with an environmental protection rating according to the recent industrial standards.

     A metal dust cap is great for protecting the chassis from EMI or noise.

     It is advisable to secure the dust cap to the chassis so that the cap is there the next time it is needed.

     It is important to ensure that the chain is of an appropriate length as a longer chain may cover or prevent access to other connectors.

     In case, the cover is not permanently attached to the connector, leave room on the back panel so that the chain can be attached to the rear panel.

     While inserting the pipe end caps on a ferrule, don’t insert it all the way since small dust particles can accumulate the bottom of the cap.

     The smaller the eyelet or attachment point is, chain attachment point takes up that much less amount of rear panel space.

    You need to perform an extensive survey of the kinds of dust covers available as here are different models of rim dust covers depending on the type of gas or liquid flowing through the material. To choose a dust cap with a chain or a plug & chain instrument depends on upon your specific requirements. Knowledgeable experts are the ones you need to consult here. JTC Valve Sales has been industry leaders in the supply of industrial regulators/valves and their accessories. Having more than 24 years’ experience in serving industry needs, JTC Valve Sales serves its clients in the best possible manner.

4 Item(s)

 -   +